Home › Forums › Everything about everything else › Help Guys

Viewing 15 posts - 1 through 15 (of 24 total)
1 2
  • Author
    Posts
  • 8 January, 2016 at 20:11 #24322
    O to the o
    Participant

    Hi

    Today I tried to install a buzzer/ beeper on my mini Tricopter.
    I soldered it on, conneted it via Usb to cleanflight, configuerd the buzzer, deconnected it and tried.
    It was not working. Than I desoldered the buzzer, but now the Naze32 wont even connect to the Pc.
    If I try the connection fails and the green and red leds on the Pcb are flashing.

    I use the Mini-Tricopter-kit whith Naze and Powerd.Bord and the Electronicskit.

    I hope you guys can help me.

    8 January, 2016 at 23:27 #24331
    O to the o
    Participant

    And the bootloader is not responding … 🙁 oh i hate this fucking day

    9 January, 2016 at 05:12 #24341
    donnyb
    Participant

    Hold on! Don’t panic…. It didn’t lose the magic smoke it might be fine. check for solder bridge near the area you soldered and opposite side. Just go over it really good to make sure you didn’t add too much solder.

    9 January, 2016 at 05:23 #24342
    donnyb
    Participant

    I forgot. Make sure you didn’t de-solder anything other than what you installed.

    If you look at the board closely you may be able to hook up a ftdi cable to it… You would have to ask Dave.

    9 January, 2016 at 08:59 #24345
    Terje
    Moderator

    Have you tried re-flashing the integrated Naze32 board with the boot pads shorted? Be aware that the pads are covered in a thin layer of anti-corrosion stuff that you need to scratch off first.

    9 January, 2016 at 10:56 #24353
    O to the o
    Participant

    No i dont tried that where do i find the bootpins ? And how can i do it ?

    9 January, 2016 at 17:24 #24376
    O to the o
    Participant

    Now i tried it but it didnt helped me 🙁
    I can flash a new firmware but than the binking starts agian after the flashing and i cant connect to the board.
    Here is a video of the blinking leds: https://youtu.be/XqyZrEAbx3o

    9 January, 2016 at 19:17 #24382
    donnyb
    Participant

    Hey O, Maybe you could film your computer as your flashing. If you could get the computer screen and the naze in the shot could help find a solution. Also, your a little rough with the USB connector you should be very gentle. Also upload some close up photos of solder area.

    9 January, 2016 at 20:26 #24388
    O to the o
    Participant

    When i flash the Naze it says Flashig and finishes it. When its done th leds start to bling again and the connection is lost. I wrote a email to david and if he cant help i simply order a new one

    9 January, 2016 at 20:41 #24390
    O to the o
    Participant

    A last small question: What is the best summer/buzzer i can use on the naze32 ? and what is the max soldering tempreture i should use ?

    9 January, 2016 at 22:03 #24398
    GAntonjo
    Moderator

    @o-to-the-o: Which firmware and version are you flashing to your Naze? There were some versions that did not reconnect by itself after the Naze booted. Solution then was to disconnect and reconnect the USB cable. The problem is solved in later versions of TriFlight (at least).

    9 January, 2016 at 22:13 #24399
    O to the o
    Participant

    I use the newest version of Triflight from the mini Tricopter product page

    9 January, 2016 at 22:20 #24401
    O to the o
    Participant

    Maybe a static charge killed a chip or the bootloader.

    9 January, 2016 at 22:22 #24402
    GAntonjo
    Moderator

    I have also heard people having problems with certain USB cables and using another cable solve their connection problems.

    9 January, 2016 at 22:42 #24405
    O to the o
    Participant

    I tried three cabels all worked before with the naze32

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 24 total)
1 2
  • The forum ‘Everything about everything else’ is closed to new topics and replies.