Forum Replies Created

Viewing 12 posts - 1 through 12 (of 12 total)
  • Author
    Posts
  • 28 June, 2016 at 01:12 in reply to: F3FC Aux pass through for gimbal #30193
    Achim
    Participant

    @GAntonjo:
    Sounds Great ?
    Thank you!

    3 May, 2016 at 19:26 in reply to: Idea for TriFlight (aka Naze32) Frame V2? #28386
    Achim
    Participant

    Any news? Since I killed my NAZE main board by attempting to ad the MinimOSD I am very keen on an update. Sorry for my impatience.
    I am very keen on OSD f3 Processor and Amperemeter.

    BTW
    A gimbal would also be a great!
    Thank you all for your great work especially David and Lauka

    25 January, 2016 at 00:54 in reply to: Micro MinimOsd #25111
    Achim
    Participant

    Hello Rue, guess you are right. Seems very similar to the topic you found (post 17001).
    My wiring is the nearly the same as you posted, but I used the 5v and ground on the right instead of the one to TX RX and I didn’t connect RSSI. Do you think that might be an issue?
    Thank you!

    24 January, 2016 at 10:03 in reply to: Micro MinimOsd #25075
    Achim
    Participant

    Thank you!
    I soldered video in and out, the Rx,the Tx, batt 1 an the ground next to it to the Main Batterie and the solitude standing pats with 5v in and the Ground next to it to the 5v PDB circuit. The NAZE doesn’t light up anymore. 🙁

    24 January, 2016 at 02:27 in reply to: Micro MinimOsd #25067
    Achim
    Participant

    Finally I added the Minimosd and placed it in the front spacer. Unfortunately (stupidly) I forgot that it uses USRT1 together with the usb. So as I hooked up the NAZE32 to Cleanflight it took a short while and then I smelled the holy smoke as I also powered up the Minimosd. Now I don’t get any connection to my NAZE anymore. The OSD still works. Is it possible to fry the NAZE only by that or should I look for another short?

    16 September, 2015 at 17:57 in reply to: Micro MinimOsd #19670
    Achim
    Participant

    Thank you very much! What is the UART1 or UART2 Port on the integrated Naze32? I assume it is the one opposite the sub port labelled tx(=UART1) an Rx (=Uart2). Is this correct?
    I use a spektrum transmitter with AR 8000 receiver so it is not cppm. Is that an issue?
    Regards!

    15 September, 2015 at 12:04 in reply to: Naze32: No Throttle Response #19615
    Achim
    Participant

    Hello again!
    Thanks Leo again, I rechecked everything and it is not the Throttle Hold. I set everything entirely new up with reflashing the board without success. I think the board is defect. I reordered one together with a mini and will recheck with the new board.

    26 August, 2015 at 06:59 in reply to: Naze32: No Throttle Response #18602
    Achim
    Participant

    Sorry, i can’t work I the problem, because I am on holiday. I use a Spektrum dx9 and a ar8000 receiver. Regards

    22 August, 2015 at 16:02 in reply to: Naze32: No Throttle Response #18454
    Achim
    Participant

    Thanks Leo! Yes battery was plugged in. The plugg was right way round and same as the others.
    The minimum maximum is at the receiver Tab is 1500 same as there would be nothing plugged in. All other tabs are moving normally. If I switch aileron and throttle I can move the roll with the Throttle stick but still no response on the throttle channel if I move aileron. I can’t measure the voltage. I use a dx9 with a at 8000 so it’s PWM. Seems to be a uncommon problem. Thanks again.

    22 August, 2015 at 08:51 in reply to: Help needed with SiLabs USBtoUART VCP #18448
    Achim
    Participant

    I had the problem when my acroslim UAV flash device was plugged in and parallels was running. The naze was not visible. As I closed parallels and unplugged the Afroslim usb device it worked

    22 August, 2015 at 08:43 in reply to: Naze32: No Throttle Response #18447
    Achim
    Participant

    Thanks Leo!
    The Receiver Tab does not move. The other tabs are moving normally. I resoldered the pin 1 where the Throttle signal goes in although it Rasheed and looked perfect. The receiver gives out a throttle signal. I changed the wire as well and used the aileron signal just to try. Still no movement of the throttle tab.
    Of course I tried the steps armed and unarmed.
    Any thoughts?

    27 July, 2015 at 19:41 in reply to: Naze 32 Full Tricopter Frame #17727
    Achim
    Participant

    A GPS / Baro / Compass add on would be fantastic! But I am also very keen on your mini !
    Keep up your fantastic work!

  • Author
    Posts
Viewing 12 posts - 1 through 12 (of 12 total)