Forum Replies Created
I decided to post a page from hk. There listed as multi rotor lipos. http://hobbyking.com/hobbyking/store/__1387__85__Batteries_Accessories-Multirotor_Lipoly.html
I’ve always thought you would want the higher C rating.
It might be a good idea to pull off the props and wind it up to feel if you have a unbalanced motor. Also a slight bent shaft Will give you some hi pitch vibes. Also feel if everything is snug. I’ve ran into all of the above. Actually I’ve had motors come out from the mount. On my mobius I keep in in the holder. Before you stick velcro on the bottom you might want to remove the rubberized coating. I don’t even strap it down.
Actually i would like to see a Y6 mini. Lol You wouldn’t catch that in your hand!
Unfortunately that’s the downside to the international shipping. One of the only reasons I buy most of the stuff all ready imported. I do pay more and pay extra for the shipping, but on a Tim limit. It pays itself off. I think some of the local hobby shops should carry Daves tricopter in stock. Maybe flitetest…
@Ruiz It shouldn’t take that long in in Chicago. I would call them up. A week is a long time for your package to sit there. I’m over in ky next to Cincinnati and so far the longest international order has taken 20 days. The shortest is about 10 days. I would get a description including weight color and physical measurements of the package and see if if it could be lost.22 June, 2015 at 19:00 in reply to: A glimpse of the RCExplorer mini tricopter by David Windestål #16374
I think David and flitetest really compliment each other.
I would like to see some videos also! I bet it will be nibble! I thought about designing one! But I built the hk thorax. So I will have to build up some cash. Lol
That was supposed to say tricopter. Lol
I think it was a great interview. I also think that the difference between the quad and the trickster needs a video along with commentary to really describe the difference. While flying show the swooppyness would bring the trickster in a new light.
Hey I wwould get a sd card with nothing on it and put it in the mobius. If the mobius software is responding to your camera you may try to format the card with the mobius software. Actually if you have the video out cable if the yellow light is on it may be putting out a live video signal!
If that don’t get the buttons working. There is a forum on rc groups with everything you may come a crossed.
You may be able to save it.
Bit if not don’t feel bad, it wasn’t a gopro!
Hey when you get some footage from the new camera maybe do a review with some footage and a few photos.
Hey don’t give up hope yet. Something else you may try. Now it has the firmware and seems like it installed ok. Pop open the case with a #0 Philips screw driver and remove the two screws on the bottom. Gently pry the case apart and pull the battery connector off and Waite a minute. Then put the connector from the battery back on. Hit and hold on the power button for 2 seconds. It may boot up.
Hi 2ma! I’ve seen article on rcgroups about the firmware. I would get a sdcard reader plug it in to you computer and drop firmware 1.20 on the card. Not using the mobius. Plug the sd card in to the mobius. Hold the power button till it blinks. Let go of the button.
Some of the newer firmware isn’t that great. And if it works fine don’t change it.
I updated mine one time, only to switch back.
Hope that helps.
That’s a pretty tall order.
Actual ly those are the ones I bought that didn’t work. I ended up buying a double male rca connector. Is the cable the original that came with your video receiver? The connector on your cable may be inverted. Meaning that the center connector might be connected to the outer connector. Kind of like a component Cable.
Hi all, I’ve had a similar problem with the yaw on my multiwii hex. I’ve read article where you can raise the p gains on the yaw and help stop it. It helped a bit but I also had to trim the radio. I flew my tri copter yesterday. Seemed like I could not get enough yaw. But still battled the drift. I’m using the flysky radio and receive. (Cheap) But I’m going to set everything up for frsky taranis. I’m going to work with the pids on the yaw.
If you find out anything please post it.