Forum Replies Created
-
AuthorPosts
-
DraclickaParticipant
I hear you. Nothing wrong with asking questions! I’m here to find out the same thing.
DraclickaParticipantThanks LitterBug, you have given me a great place to start. Much appreciated!
(edit)
I should also add that I have the simple on/off light strips currently, but am looking for something more advanced and will look at your suggestions.
DraclickaParticipantI decided to flash the board and start over. This time around I’m not getting the beeping.
DraclickaParticipantnoir522, sorry, because I didn’t perform the fix I don’t know which pins were involved. I suggest trying adding fresh solder to all of the pads on your board to see if that will fix your problem.
DraclickaParticipantStock RCE parts. Frsky receiver.
Attachments:
DraclickaParticipantSorry for the late reply, I haven’t been on here in a while.
I sent my board in to RCExplorer and the problem was found/fixed. Here’s what I was told:
“There was a micro solder bridge between two of the pins on the pinheader. One of these tiny spikes were shorting out one of the I2C’s to ground. Just added some fresh solder to the pads and the baro jumped back to life.”
Hope that helps you!
Jason
DraclickaParticipantRemoved my comment due to no response from the community. Will start a new thread with my question.
DraclickaParticipantVBAT seems pretty consistent in Cleanflight, however there were minor fluctuations observed. Link to VBAT, sensors tab and motors videos below.
During the recordings I held in air to avoid wobbling caused by tail servo.
Interesting to see barometer graph change so much since I was holding it at approx the same place in the air.
Vbat window video:
https://youtu.be/TC9iJur0kvoSensors tab video:
https://youtu.be/hneZ-dU-e1gMotors tab video:
https://youtu.be/QLWMgklgaVoThanks,
Jason
DraclickaParticipantJust noticed errors at the bottom of the Cleanflight interface (not sure if they’re related to the glitching though), see screenshot.
Attachments:
DraclickaParticipantUpdate:
• rebuilt tail boom with all new parts (servo, motor, ESC and wiring)
• checked all connections on the board
• replaced the recieverSTILL GLITCHES
Video on YouTube: https://youtu.be/EskbDvdVy9g
DraclickaParticipantNeed to get a camera in the air this weekend…
DraclickaParticipantI should also add that I tried resetting all the settings in CleanFlight back to defaults (started with a clean flash), which resulted in no change… still getting the glitching.
DraclickaParticipantThanks for the input David and hertz.
I’m running the Little Bee 30A ESCs that I purchased from the RCE shop. ONESHOT is enabled in the FC. I am running the latest Triflight version (I have also tried an earlier version with no luck). You are correct David, nothing else is attached to the F3FC.
Very perplexed right now…
DraclickaParticipantThanks Terje. I’m getting a blue flashing LED whenever I power up, or plug in the USB. The buzzer is also blaring in sync to the flashing. Wouldn’t this be directly related to the board itself?
Can someone please tell what the each LED color means on the F3FC board?
Very surprising that I can’t find documentation for something so basic.
Attachments:
4 August, 2016 at 22:27 in reply to: Where in the world is your RCExplorer Copter? Link to map #31981DraclickaParticipantCampbell, CA (San Francisco Bay Area)
-
AuthorPosts